-- DSL Node Statistical Data Base Enterprise Mib -- -- Lucent Technologies -- 1275 Harbor Bay Pkwy -- Alameda, CA 94502 -- +1 510 769 6001 -- info@ascend.com -- -- Copyright (c) 1993-2000 Lucent Technologies -- All rights reserved. -- -- This group contains MIB variables used to provide statistical information -- defined by the DSL Standards EOC sections. Information provided in this -- MIB is available for local ports and the remote nodes for a specific -- interfaces. -- -- Entries are indexed via the DSLIfIndex, the interface being referred to, -- DSLNodeId, the ID of the node in the DSL path, bucketIndex, the -- time interval for a given data set. -- -- Eoc Data Base Status -- Displays static information learned right after training. -- -- Eoc Data Base 15 minute statistics -- Displays up to 96 bins of 15 minute statistics. -- You mileage might vary as some standards require less bins for a given -- interface type. -- -- Eoc Data Base 24 hour statistics -- Displays up to 8 bins of 24 hour statistics. -- -- CVS ID: $Id: eocstat.mib,v 29.1 2000/04/14 13:27:25 cmiller Exp $ -- -- 03-20-2000: Initial release -- ASCEND-DSL-EOC-MIB DEFINITIONS ::= BEGIN IMPORTS wanTypeDslEoc FROM ASCEND-WAN-MIB OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB Gauge32, Integer32 FROM SNMPv2-SMI-v1 InterfaceIndex FROM IF-MIB; -- -- Naming Conventions: -- Curr - Current -- Atn - Attenuation -- CVs - Coding Violations -- ESs - Error Seconds -- SESs - Severely Error Seconds -- LoSWs - Loss of Sync Words -- UAs - Unavailable Seconds -- Snr - Signal to Noise Ratio -- Mgn - Margin -- DslEocNodeID ::= INTEGER { other( 1 ), -- None of the following. coe( 2 ), -- Central Office Equipment. cpe( 3 ), -- Customer Premises. repeater1( 4 ), -- Repeater 1. repeater2( 5 ), -- Repeater 2. repeater3( 6 ), -- Repeater 3. repeater4( 7 ), -- Repeater 4. repeater5( 8 ), -- Repeater 5. repeater6( 9 ), -- Repeater 6. repeater7( 10 ), -- Repeater 7. repeater8( 11 ) -- Repeater 8. } DslEoc15MinInterval ::= INTEGER ( 1..96 ) DslEoc24HourInterval ::= INTEGER ( 1..7 ) -- -- The EOC Status table contains all the static EOC information -- learned once at the beginning of connection and some global -- statistics not included in the bins. -- dslEocCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF DslEocCurrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "DSL interface EOC data base table." ::= { wanTypeDslEoc 1 } dslEocCurrEntry OBJECT-TYPE SYNTAX DslEocCurrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "DSL Interface EOC data base entry." INDEX { dslEocCurrIfIndex, dslEocCurrNodeIndex } ::= { dslEocCurrTable 1 } DslEocCurrEntry ::= SEQUENCE { dslEocCurrIfIndex InterfaceIndex, dslEocCurrNodeIndex DslEocNodeID, dslEocCurrHopCount INTEGER, dslEocCurrCountryCode INTEGER, dslEocCurrProviderCode DisplayString, dslEocCurrVendorEocSwVer INTEGER, dslEocCurrStandardVersion INTEGER, dslEocCurrVendorSwVer DisplayString, dslEocCurrVendorModelNo DisplayString, dslEocCurrVendorSerialNo DisplayString, dslEocCurrNetworkSnrMgn INTEGER, dslEocCurrCustSnrMgn INTEGER, dslEocCurrAtn INTEGER, dslEocCurrCVs INTEGER, dslEocCurrESs INTEGER, dslEocCurrSESs INTEGER, dslEocCurrLoSWs INTEGER, dslEocCurrUASs INTEGER } dslEocCurrIfIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "Interface group index assigned to this port." ::= { dslEocCurrEntry 1 } dslEocCurrNodeIndex OBJECT-TYPE SYNTAX DslEocNodeID ACCESS read-only STATUS mandatory DESCRIPTION "DSL IDs for local and remote nodes. Used to index into the correct node entry." ::= { dslEocCurrEntry 2 } dslEocCurrHopCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of hops between the COE and this node." ::= { dslEocCurrEntry 3 } dslEocCurrCountryCode OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Remote nodes country code. Refer to ITU CCITT T.35 specification for country code value. " ::= { dslEocCurrEntry 4 } dslEocCurrProviderCode OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Remote nodes provider code. Refer to ITU ANSI T1.220 specification for provider code value." ::= { dslEocCurrEntry 5 } dslEocCurrVendorEocSwVer OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "EOC software version identifier." ::= { dslEocCurrEntry 6 } dslEocCurrStandardVersion OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "T1E1.4 DSL Standard Version identifier." ::= { dslEocCurrEntry 7 } dslEocCurrVendorSwVer OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Vendors software version." ::= { dslEocCurrEntry 8 } dslEocCurrVendorModelNo OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Vendors model number." ::= { dslEocCurrEntry 9 } dslEocCurrVendorSerialNo OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Vendors node serial number." ::= { dslEocCurrEntry 10 } dslEocCurrNetworkSnrMgn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current network signal quality." ::= { dslEocCurrEntry 11 } dslEocCurrCustSnrMgn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current customer signal quality." ::= { dslEocCurrEntry 12 } dslEocCurrAtn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current loop attenuation." ::= { dslEocCurrEntry 13 } dslEocCurrCVs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line is defined as a count of DSL CRC anomalies occurring during the accumulation period." ::= { dslEocCurrEntry 14 } dslEocCurrESs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Error second is defined as a count of 1 second intervals during which one or more CRC anomalies are declared and/or one or more LOSW defects are declared." ::= { dslEocCurrEntry 15 } dslEocCurrSESs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line is defined as a count of 1 second intervals for during which at least 50 CRC anomalies are declared or one or more LOSW defects are declared." ::= { dslEocCurrEntry 16 } dslEocCurrLoSWs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An LOSW defect is declared when at least 3 consecutive received frames contain one or more errors in the framing bits. This object counts the number of seconds during which Loss of Sync Word was detected." ::= { dslEocCurrEntry 17 } dslEocCurrUASs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line is a count of 1 second intervals for which the DSL line is unavailable. The HDSL2 line becomes unavailable at the onset of 10 contiguous SES-L's. Once unavailable the DSL line becomes available at the onset of 10 contiguous seconds with no SES-L's." ::= { dslEocCurrEntry 18 } -- -- 15 Minute statistics table. The first entry is always the current -- table entry. The nth entries starts with the latest and displays -- the oldest entry last. -- dslEoc15Table OBJECT-TYPE SYNTAX SEQUENCE OF DslEoc15Entry ACCESS not-accessible STATUS mandatory DESCRIPTION "Up to 96 bins each containing 15 minutes of accumulated statistics." ::= { wanTypeDslEoc 2 } dslEoc15Entry OBJECT-TYPE SYNTAX DslEoc15Entry ACCESS not-accessible STATUS mandatory DESCRIPTION "A interface statistical entry." INDEX { dslEoc15IfIndex, dslEoc15NodeIndex, dslEoc15BinIndex } ::= { dslEoc15Table 1 } DslEoc15Entry ::= SEQUENCE { dslEoc15IfIndex InterfaceIndex, dslEoc15NodeIndex DslEocNodeID, dslEoc15BinIndex DslEoc15MinInterval, dslEoc15CVs INTEGER, dslEoc15ESs INTEGER, dslEoc15SESs INTEGER, dslEoc15LoSWs INTEGER, dslEoc15UASs INTEGER } dslEoc15IfIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "Interface group index assigned to this port." ::= { dslEoc15Entry 1 } dslEoc15NodeIndex OBJECT-TYPE SYNTAX DslEocNodeID ACCESS read-only STATUS mandatory DESCRIPTION "DSL IDs for local and remote nodes." ::= { dslEoc15Entry 2 } dslEoc15BinIndex OBJECT-TYPE SYNTAX DslEoc15MinInterval ACCESS read-only STATUS mandatory DESCRIPTION "DSL modules bin ID." ::= { dslEoc15Entry 3 } dslEoc15CVs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line is defined as a count of DSL CRC anomalies occurring during the accumulation period." ::= { dslEoc15Entry 4 } dslEoc15ESs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Error second is defined as a count of 1 second intervals during which one or more CRC anomalies are declared and/or one or more LOSW defects are declared." ::= { dslEoc15Entry 5 } dslEoc15SESs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line is defined as a count of 1 second intervals for during which at least 50 CRC anomalies are declared or one or more LOSW defects are declared." ::= { dslEoc15Entry 6 } dslEoc15LoSWs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An LOSW defect is declared when at least 3 consecutive received frames contain one or more errors in the framing bits. This object counts the number of seconds during which Loss of Sync Word was detected." ::= { dslEoc15Entry 7 } dslEoc15UASs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line is a count of 1 second intervals for which the DSL line is unavailable. The HDSL2 line becomes unavailable at the onset of 10 contiguous SES-L's. Once unavailable the DSL line becomes available at the onset of 10 contiguous seconds with no SES-L's." ::= { dslEoc15Entry 8 } -- -- 24 hour statistics table. The first entry is always the current -- table entry. The nth entry is previous 24 hour table entries. -- dslEoc24Table OBJECT-TYPE SYNTAX SEQUENCE OF DslEoc24Entry ACCESS not-accessible STATUS mandatory DESCRIPTION "Up to 7 bins each containing 24 hours of accumulated statistics." ::= { wanTypeDslEoc 3 } dslEoc24Entry OBJECT-TYPE SYNTAX DslEoc24Entry ACCESS not-accessible STATUS mandatory DESCRIPTION "A interface statistical entry." INDEX { dslEoc24IfIndex, dslEoc24NodeIndex, dslEoc24BinIndex } ::= { dslEoc24Table 1 } DslEoc24Entry ::= SEQUENCE { dslEoc24IfIndex InterfaceIndex, dslEoc24NodeIndex DslEocNodeID, dslEoc24BinIndex DslEoc24HourInterval, dslEoc24CVs INTEGER, dslEoc24ESs INTEGER, dslEoc24SESs INTEGER, dslEoc24LoSWs INTEGER, dslEoc24UASs INTEGER } dslEoc24IfIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "Interface group index assigned to this port." ::= { dslEoc24Entry 1 } dslEoc24NodeIndex OBJECT-TYPE SYNTAX DslEocNodeID ACCESS read-only STATUS mandatory DESCRIPTION "DSL IDs for local and remote nodes." ::= { dslEoc24Entry 2 } dslEoc24BinIndex OBJECT-TYPE SYNTAX DslEoc24HourInterval ACCESS read-only STATUS mandatory DESCRIPTION "DSL modules bin ID." ::= { dslEoc24Entry 3 } dslEoc24CVs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line is defined as a count of DSL CRC anomalies occurring during the accumulation period." ::= { dslEoc24Entry 4 } dslEoc24ESs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Error second is defined as a count of 1 second intervals during which one or more CRC anomalies are declared and/or one or more LOSW defects are declared." ::= { dslEoc24Entry 5 } dslEoc24SESs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line is defined as a count of 1 second intervals for during which at least 50 CRC anomalies are declared or one or more LOSW defects are declared." ::= { dslEoc24Entry 6 } dslEoc24LoSWs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An LOSW defect is declared when at least 3 consecutive received frames contain one or more errors in the framing bits. This object counts the number of seconds during which Loss of Sync Word was detected." ::= { dslEoc24Entry 7 } dslEoc24UASs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line is a count of 1 second intervals for which the DSL line is unavailable. The HDSL2 line becomes unavailable at the onset of 10 contiguous SES-L's. Once unavailable the DSL line becomes available at the onset of 10 contiguous seconds with no SES-L's." ::= { dslEoc24Entry 8 } END