-- $Id: rfc2515.mib,v 1.1.24.1 1999/08/11 05:27:53 aarunach Exp $ -- -- RFC 2515 ATM Management Objects -- 14 May 99: Initial release. RFC 2515 is based on SNMPv2 MIB. This -- MIB has been modified to support only SNMPv1 -- -- Modified v2 based syntax to v1 based syntax -- The following are the changes made: -- * Moved the definition of atmMIB and atmMIBObjects to rfc2514.mib -- * All the mib fields that have STATUS as current are changed to -- manadatory. -- * syntax MAX-ACCESS has been changed to ACCESS for all the -- fields. -- * atmTrafficDescrParamIndex is made read-only -- * Since we don't have read-create ACCESS for mibfields with read-create -- access were changed to read-write. -- * atmInterfaceConfEntry parameters are changed from read-write to -- read-only since set functions are not supported. -- * atmVclReceiveTrafficDescrIndex and atmVclTransmitTrafficDescrIndex -- and atmVclAdminStatus in atmVclTable are changed from read-write to -- read-only. Similarly atmVccAalType, atmVccAal5CpcsTransmitSduSize, -- atmVccAal5CpcsReceiveSduSize, atmVccAal5EncapsType, atmVclRowStatus, -- atmVclCastType and atmVclConnKind in atmVclTable are changed from -- read-write to read-only. These changes are made since set -- functions are not supported. -- * The following tables are commented out since they are not supported -- atmVpCrossConnectTable and atmVcCrossConnectTable. ATM-MIB DEFINITIONS ::= BEGIN IMPORTS -- MODULE-IDENTITY, OBJECT-TYPE, -- Counter32, Integer32, IpAddress, mib-2 -- FROM SNMPv2-SMI -- DisplayString, RowStatus, TruthValue -- FROM SNMPv2-TC -- MODULE-COMPLIANCE, OBJECT-GROUP -- FROM SNMPv2-CONF InterfaceIndex, ifIndex FROM IF-MIB AtmAddr, AtmConnKind, AtmConnCastType, AtmServiceCategory, AtmTrafficDescrParamIndex, AtmVpIdentifier, AtmVcIdentifier, AtmVorXAdminStatus, AtmVorXLastChange, AtmVorXOperStatus, atmNoClpNoScr, atmMIB, atmMIBObjects FROM ATM-TC-MIB IpAddress, TimeTicks FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 Counter32, Integer32, TimeStamp, RowStatus, TruthValue FROM SNMPv2-SMI-v1 mib-2, DisplayString FROM RFC1213-MIB; -- atmMIB MODULE-IDENTITY -- LAST-UPDATED "9810191200Z" -- ORGANIZATION "IETF AToM MIB Working Group" -- CONTACT-INFO -- " Kaj Tesink -- Postal: Bellcore -- 331 Newman Springs Road -- Red Bank, NJ 07701 -- Tel: 732-758-5254 -- Fax: 732-758-2269 -- E-mail: kaj@bellcore.com" -- DESCRIPTION -- "This is the MIB Module for ATM and AAL5-related -- objects for managing ATM interfaces, ATM virtual -- links, ATM cross-connects, AAL5 entities, and -- and AAL5 connections." -- REVISION "9810191200Z" -- DESCRIPTION -- "The initial revision of this module was published -- as RFC 1695. Key revisions include: -- o Textual Conventions and OBJECT IDENTITIES have -- been moved to a separate MIB module. -- o Applicability of objects to PVCs, SVCs and Soft -- PVCs has been clarified. -- o DEFVAL clauses have been added. -- o The relationship of ifIndex values with different -- layers and sublayers related to ATM has been -- clarified. -- o atmTrafficQosClass has been deprecated -- and replaced with atmServiceCategory. -- o atmInterfaceCurrentMaxVpiBits and -- atmInterfaceCurrentMaxVciBits have been added with -- a description on their relationship with other -- objects. -- o atmInterfaceAddressType and atmInterfaceAdminAddress -- have been deprecated and replaced by -- atmInterfaceSubscrAddress. -- o atmInterfaceTCAlarmState has been clarified. -- o atmTrafficDescrParamIndexNext has been introduced -- in order to provide a manager a free -- atmTrafficDescrParamIndex value. -- o The atmTrafficFrameDiscard capability has been added. -- o A connection topology type (atmVpl/VclCastType) and -- a call control type (atmVpl/VclConnKind) have been -- added. -- o aal2 has been added to atmVccAalType." -- REVISION "9406072245Z" -- DESCRIPTION -- "The RFC1695 version of this MIB module." -- ::= { mib-2 37 } -- atmMIBObjects OBJECT IDENTIFIER ::= {atmMIB 1} -- This ATM MIB Module consists of the following tables: -- (1) ATM Interface configuration table -- (2) ATM Interface DS3 PLCP table -- (3) ATM Interface TC Sublayer table -- (4) Atm Traffic Descriptor table -- (5) ATM Interface VPL configuration table -- (6) ATM Interface VCL configuration table -- (7) ATM VP Cross Connect table (for PVCs) -- (8) ATM VC Cross Connect table (for PVCs) -- (9) ATM Interface AAL5 VCC performance statistics -- table -- ATM Interface Configuration Parameters Table -- This table contains ATM specific -- configuration information associated with -- an ATM interface beyond those -- supported using the ifTable. atmInterfaceConfTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmInterfaceConfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains ATM local interface configuration parameters, one entry per ATM interface port." ::= { atmMIBObjects 2 } atmInterfaceConfEntry OBJECT-TYPE SYNTAX AtmInterfaceConfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains ATM interface configuration parameters and state variables and is indexed by ifIndex values of ATM interfaces." INDEX { ifIndex } ::= { atmInterfaceConfTable 1} AtmInterfaceConfEntry ::= SEQUENCE { atmInterfaceMaxVpcs INTEGER, atmInterfaceMaxVccs INTEGER, atmInterfaceConfVpcs INTEGER, atmInterfaceConfVccs INTEGER, atmInterfaceMaxActiveVpiBits INTEGER, atmInterfaceMaxActiveVciBits INTEGER, atmInterfaceIlmiVpi AtmVpIdentifier, atmInterfaceIlmiVci AtmVcIdentifier, atmInterfaceAddressType INTEGER, atmInterfaceAdminAddress AtmAddr, atmInterfaceMyNeighborIpAddress IpAddress, atmInterfaceMyNeighborIfName DisplayString, atmInterfaceCurrentMaxVpiBits INTEGER, atmInterfaceCurrentMaxVciBits INTEGER, atmInterfaceSubscrAddress AtmAddr } atmInterfaceMaxVpcs OBJECT-TYPE SYNTAX INTEGER (0..4096) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of VPCs (PVPCs and SVPCs) supported at this ATM interface. At the ATM UNI, the maximum number of VPCs (PVPCs and SVPCs) ranges from 0 to 256 only." ::= { atmInterfaceConfEntry 1} atmInterfaceMaxVccs OBJECT-TYPE SYNTAX INTEGER (0..65536) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of VCCs (PVCCs and SVCCs) supported at this ATM interface." ::= { atmInterfaceConfEntry 2} atmInterfaceConfVpcs OBJECT-TYPE SYNTAX INTEGER (0..4096) ACCESS read-only STATUS mandatory DESCRIPTION "The number of VPCs (PVPC, Soft PVPC and SVPC) currently in use at this ATM interface. It includes the number of PVPCs and Soft PVPCs that are configured at the interface, plus the number of SVPCs that are currently established at the interface. At the ATM UNI, the configured number of VPCs (PVPCs and SVPCs) can range from 0 to 256 only." ::= { atmInterfaceConfEntry 3} atmInterfaceConfVccs OBJECT-TYPE SYNTAX INTEGER (0..65536) ACCESS read-only STATUS mandatory DESCRIPTION "The number of VCCs (PVCC, Soft PVCC and SVCC) currently in use at this ATM interface. It includes the number of PVCCs and Soft PVCCs that are configured at the interface, plus the number of SVCCs that are currently established at the interface." ::= { atmInterfaceConfEntry 4} atmInterfaceMaxActiveVpiBits OBJECT-TYPE SYNTAX INTEGER (0..12) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of active VPI bits configured for use at the ATM interface. At the ATM UNI, the maximum number of active VPI bits configured for use ranges from 0 to 8 only." ::= { atmInterfaceConfEntry 5} atmInterfaceMaxActiveVciBits OBJECT-TYPE SYNTAX INTEGER (0..16) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of active VCI bits configured for use at this ATM interface." ::= { atmInterfaceConfEntry 6} atmInterfaceIlmiVpi OBJECT-TYPE SYNTAX AtmVpIdentifier ACCESS read-only STATUS mandatory DESCRIPTION "The VPI value of the VCC supporting the ILMI at this ATM interface. If the values of atmInterfaceIlmiVpi and atmInterfaceIlmiVci are both equal to zero then the ILMI is not supported at this ATM interface." DEFVAL { 0 } ::= { atmInterfaceConfEntry 7} atmInterfaceIlmiVci OBJECT-TYPE SYNTAX AtmVcIdentifier ACCESS read-only STATUS mandatory DESCRIPTION "The VCI value of the VCC supporting the ILMI at this ATM interface. If the values of atmInterfaceIlmiVpi and atmInterfaceIlmiVci are both equal to zero then the ILMI is not supported at this ATM interface." DEFVAL { 16 } ::= { atmInterfaceConfEntry 8} atmInterfaceAddressType OBJECT-TYPE SYNTAX INTEGER { private(1), nsapE164(2), nativeE164(3), other(4) } ACCESS read-only STATUS deprecated DESCRIPTION "The type of primary ATM address configured for use at this ATM interface." ::= { atmInterfaceConfEntry 9 } -- The atmInterfaceAdminAddress object has been replaced by -- atmInterfaceSubscrAddress. atmInterfaceAdminAddress OBJECT-TYPE SYNTAX AtmAddr ACCESS read-only STATUS deprecated DESCRIPTION "The primary address assigned for administrative purposes, for example, an address associated with the service provider side of a public network UNI (thus, the value of this address corresponds with the value of ifPhysAddress at the host side). If this interface has no assigned administrative address, or when the address used for administrative purposes is the same as that used for ifPhysAddress, then this is an octet string of zero length." ::= { atmInterfaceConfEntry 10 } atmInterfaceMyNeighborIpAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the neighbor system connected to the far end of this interface, to which a Network Management Station can send SNMP messages, as IP datagrams sent to UDP port 161, in order to access network management information concerning the operation of that system. Note that the value of this object may be obtained in different ways, e.g., by manual configuration, or through ILMI interaction with the neighbor system." ::= { atmInterfaceConfEntry 11 } atmInterfaceMyNeighborIfName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The textual name of the interface on the neighbor system on the far end of this interface, and to which this interface connects. If the neighbor system is manageable through SNMP and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. If this interface does not have a textual name, the value of this object is a zero length string. Note that the value of this object may be obtained in different ways, e.g., by manual configuration, or through ILMI interaction with the neighbor system." ::= { atmInterfaceConfEntry 12 } atmInterfaceCurrentMaxVpiBits OBJECT-TYPE SYNTAX INTEGER (0..12) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of VPI Bits that may currently be used at this ATM interface. The value is the minimum of atmInterfaceMaxActiveVpiBits, and the atmInterfaceMaxActiveVpiBits of the interface's UNI/NNI peer. If the interface does not negotiate with its peer to determine the number of VPI Bits that can be used on the interface, then the value of this object must equal atmInterfaceMaxActiveVpiBits." ::= { atmInterfaceConfEntry 13 } atmInterfaceCurrentMaxVciBits OBJECT-TYPE SYNTAX INTEGER (0..16) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of VCI Bits that may currently be used at this ATM interface. The value is the minimum of atmInterfaceMaxActiveVciBits, and the atmInterfaceMaxActiveVciBits of the interface's UNI/NNI peer. If the interface does not negotiate with its peer to determine the number of VCI Bits that can be used on the interface, then the value of this object must equal atmInterfaceMaxActiveVciBits." ::= { atmInterfaceConfEntry 14 } atmInterfaceSubscrAddress OBJECT-TYPE SYNTAX AtmAddr ACCESS read-only STATUS mandatory DESCRIPTION "The identifier assigned by a service provider to the network side of a public network UNI. If this interface has no assigned service provider address, or for other interfaces this is an octet string of zero length." ::= { atmInterfaceConfEntry 15 } -- The ATM Interface DS3 PLCP Table -- This table contains the DS3 PLCP configuration and -- state parameters of those ATM interfaces -- which use DS3 PLCP for carrying ATM cells over DS3. atmInterfaceDs3PlcpTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmInterfaceDs3PlcpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains ATM interface DS3 PLCP parameters and state variables, one entry per ATM interface port." ::= { atmMIBObjects 3} atmInterfaceDs3PlcpEntry OBJECT-TYPE SYNTAX AtmInterfaceDs3PlcpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains DS3 PLCP parameters and state variables at the ATM interface and is indexed by the ifIndex value of the ATM interface." INDEX { ifIndex } ::= { atmInterfaceDs3PlcpTable 1} AtmInterfaceDs3PlcpEntry ::= SEQUENCE { atmInterfaceDs3PlcpSEFSs Counter32, atmInterfaceDs3PlcpAlarmState INTEGER, atmInterfaceDs3PlcpUASs Counter32 } atmInterfaceDs3PlcpSEFSs OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of DS3 PLCP Severely Errored Framing Seconds (SEFS). Each SEFS represents a one-second interval which contains one or more SEF events." ::= { atmInterfaceDs3PlcpEntry 1} atmInterfaceDs3PlcpAlarmState OBJECT-TYPE SYNTAX INTEGER { noAlarm(1), receivedFarEndAlarm(2), incomingLOF(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates if there is an alarm present for the DS3 PLCP. The value receivedFarEndAlarm means that the DS3 PLCP has received an incoming Yellow Signal, the value incomingLOF means that the DS3 PLCP has declared a loss of frame (LOF) failure condition, and the value noAlarm means that there are no alarms present. Transition from the failure to the no alarm state occurs when no defects (e.g., LOF) are received for more than 10 seconds." ::= { atmInterfaceDs3PlcpEntry 2} atmInterfaceDs3PlcpUASs OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered by the PLCP." ::= { atmInterfaceDs3PlcpEntry 3} -- The ATM Interface TC Sublayer Table -- This table contains TC sublayer configuration and -- state parameters of those ATM interfaces -- which use TC sublayer for carrying ATM cells over -- SONET/SDH or DS3. atmInterfaceTCTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmInterfaceTCEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains ATM interface TC Sublayer parameters and state variables, one entry per ATM interface port." ::= { atmMIBObjects 4} atmInterfaceTCEntry OBJECT-TYPE SYNTAX AtmInterfaceTCEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains TC Sublayer parameters and state variables at the ATM interface and is indexed by the ifIndex value of the ATM interface." INDEX {ifIndex } ::= { atmInterfaceTCTable 1} AtmInterfaceTCEntry ::= SEQUENCE { atmInterfaceOCDEvents Counter32, atmInterfaceTCAlarmState INTEGER } atmInterfaceOCDEvents OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of times the Out of Cell Delineation (OCD) events occur. If seven consecutive ATM cells have Header Error Control (HEC) violations, an OCD event occurs. A high number of OCD events may indicate a problem with the TC Sublayer." ::= { atmInterfaceTCEntry 1} atmInterfaceTCAlarmState OBJECT-TYPE SYNTAX INTEGER { noAlarm(1), lcdFailure(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates if there is an alarm present for the TC Sublayer. The value lcdFailure(2) indicates that the TC Sublayer is currently in the Loss of Cell Delineation (LCD) defect maintenance state. The value noAlarm(1) indicates that the TC Sublayer is currently not in the LCD defect maintenance state." ::= { atmInterfaceTCEntry 2} -- ATM Traffic Descriptor Parameter Table -- This table contains a set of self-consistent -- ATM traffic parameters including the -- ATM traffic service category. -- The ATM virtual link tables (i.e., VPL and VCL tables) -- will use this ATM Traffic Descriptor table -- to assign traffic parameters and service category -- to the receive and transmit directions of -- the ATM virtual links (i.e., VPLs and VCLs). -- The ATM VPL or VCL table will indicate a row -- in the atmTrafficDescrParamTable -- using its atmTrafficDescrParamIndex value. -- The management application can then compare a set of -- ATM traffic parameters with a single value. -- If no suitable row(s) in the atmTrafficDescrParamTable -- exists, the manager must create a new row(s) in this -- table. If such a row is created, agent checks the -- sanity of that set of ATM traffic parameter values. -- The manager may use atmTrafficDescrParamIndexNext -- in order to obtain a free atmTrafficDescrParamIndex -- value. -- When creating a new row, the parameter values -- will be checked for self-consistency. -- Predefined/template rows may be supported. -- A row in the atmTrafficDescrParamTable is deleted -- by setting the atmTrafficDescrRowStatus to destroy(6). -- The agent will check whether this row is still in use -- by any entry of the atmVplTable or atmVclTable. -- The agent denies the request if the row is still in -- use. -- The ATM Traffic Descriptor Parameter Table atmTrafficDescrParamTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTrafficDescrParamEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains information on ATM traffic descriptor type and the associated parameters." ::= { atmMIBObjects 5} atmTrafficDescrParamEntry OBJECT-TYPE SYNTAX AtmTrafficDescrParamEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains ATM traffic descriptor type and the associated parameters." INDEX {atmTrafficDescrParamIndex} ::= { atmTrafficDescrParamTable 1} AtmTrafficDescrParamEntry ::= SEQUENCE { atmTrafficDescrParamIndex AtmTrafficDescrParamIndex, atmTrafficDescrType OBJECT IDENTIFIER, atmTrafficDescrParam1 Integer32, atmTrafficDescrParam2 Integer32, atmTrafficDescrParam3 Integer32, atmTrafficDescrParam4 Integer32, atmTrafficDescrParam5 Integer32, -- atmTrafficQoSClass INTEGER, atmTrafficDescrRowStatus RowStatus, atmServiceCategory AtmServiceCategory, atmTrafficFrameDiscard TruthValue } atmTrafficDescrParamIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex ACCESS read-only STATUS mandatory DESCRIPTION "This object is used by the virtual link table (i.e., VPL or VCL table) to identify the row of this table. When creating a new row in the table the value of this index may be obtained by retrieving the value of atmTrafficDescrParamIndexNext." ::= { atmTrafficDescrParamEntry 1} atmTrafficDescrType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the type of ATM traffic descriptor. The type may indicate no traffic descriptor or traffic descriptor with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmTrafficDescrParam1 atmTrafficDescrParam2 atmTrafficDescrParam3 atmTrafficDescrParam4 atmTrafficDescrParam5." DEFVAL { atmNoClpNoScr } ::= { atmTrafficDescrParamEntry 2} atmTrafficDescrParam1 OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The first parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType." DEFVAL { 0 } ::= { atmTrafficDescrParamEntry 3} atmTrafficDescrParam2 OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The second parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType." DEFVAL { 0 } ::= { atmTrafficDescrParamEntry 4} atmTrafficDescrParam3 OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The third parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType." DEFVAL { 0 } ::= { atmTrafficDescrParamEntry 5} atmTrafficDescrParam4 OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The fourth parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType." DEFVAL { 0 } ::= { atmTrafficDescrParamEntry 6} atmTrafficDescrParam5 OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The fifth parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType." DEFVAL { 0 } ::= { atmTrafficDescrParamEntry 7} -- atmTrafficQoSClass OBJECT-TYPE -- SYNTAX INTEGER (0..255) -- ACCESS read-only -- STATUS deprecated -- DESCRIPTION -- "The value of this object identifies the QoS Class. -- Four Service classes have been -- specified in the ATM Forum UNI Specification: -- Service Class A: Constant bit rate video and -- Circuit emulation -- Service Class B: Variable bit rate video/audio -- Service Class C: Connection-oriented data -- Service Class D: Connectionless data -- Four QoS classes numbered 1, 2, 3, and 4 have -- been specified with the aim to support service -- classes A, B, C, and D respectively. -- An unspecified QoS Class numbered `0' is used -- for best effort traffic." -- DEFVAL { 0 } -- ::= { atmTrafficDescrParamEntry 8} atmTrafficDescrRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table." DEFVAL { active } ::= {atmTrafficDescrParamEntry 9} atmServiceCategory OBJECT-TYPE SYNTAX AtmServiceCategory ACCESS read-only STATUS mandatory DESCRIPTION "The ATM service category." DEFVAL { ubr } ::= { atmTrafficDescrParamEntry 10} atmTrafficFrameDiscard OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "If set to 'true', this object indicates that the network is requested to treat data for this connection, in the given direction, as frames (e.g. AAL5 CPCS_PDU's) rather than as individual cells. While the precise implementation is network-specific, this treatment may for example involve discarding entire frames during congestion, rather than a few cells from many frames." DEFVAL { true } ::= { atmTrafficDescrParamEntry 11 } -- ATM Interface Virtual Path Link (VPL) Table -- This table contains configuration and state -- information of a bi-directional Virtual Path Link -- (VPL) -- This table can be used to create, delete or modify -- a VPL that is terminated in an ATM host or switch. -- This table can also be used to create, delete or -- modify a VPL which is cross-connected to another -- VPL. -- In the example below, the traffic flows on the receive -- and transmit directions of the VPLs are characterized -- by atmVplReceiveTrafficDescrIndex and -- atmVplTransmitTrafficDescrIndex respectively. -- The cross-connected VPLs are identified by -- atmVplCrossConnectIdentifier. -- ________________________________ -- | | -- VPL | ATM Host, Switch, or Network | VPL -- receive | | receive -- ========> X X <======= -- <======== X X ========> -- transmit | | transmit -- |______________________________| -- The ATM Interface VPL Table atmVplTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmVplEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Virtual Path Link (VPL) table. A bi-directional VPL is modeled as one entry in this table. This table can be used for PVCs, SVCs and Soft PVCs. Entries are not present in this table for the VPIs used by entries in the atmVclTable." ::= { atmMIBObjects 6} atmVplEntry OBJECT-TYPE SYNTAX AtmVplEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the VPL table. This entry is used to model a bi-directional VPL. To create a VPL at an ATM interface, either of the following procedures are used: Negotiated VPL establishment (1) The management application creates a VPL entry in the atmVplTable by setting atmVplRowStatus to createAndWait(5). This may fail for the following reasons: - The selected VPI value is unavailable, - The selected VPI value is in use. Otherwise, the agent creates a row and reserves the VPI value on that port. (2) The manager selects an existing row(s) in the atmTrafficDescrParamTable, thereby, selecting a set of self-consistent ATM traffic parameters and the service category for receive and transmit directions of the VPL. (2a) If no suitable row(s) in the atmTrafficDescrParamTable exists, the manager must create a new row(s) in that table. (2b) The manager characterizes the VPL's traffic parameters through setting the atmVplReceiveTrafficDescrIndex and the atmVplTransmitTrafficDescrIndex values in the VPL table, which point to the rows containing desired ATM traffic parameter values in the atmTrafficDescrParamTable. The agent will check the availability of resources and may refuse the request. If the transmit and receive service categories are inconsistent, the agent should refuse the request. (3) The manager activates the VPL by setting the the atmVplRowStatus to active(1). If this set is successful, the agent has reserved the resources to satisfy the requested traffic parameter values and the service category for that VPL. (4) If the VPL terminates a VPC in the ATM host or switch, the manager turns on the atmVplAdminStatus to up(1) to turn the VPL traffic flow on. Otherwise, the atmVpCrossConnectTable must be used to cross-connect the VPL to another VPL(s) in an ATM switch or network. One-Shot VPL Establishment A VPL may also be established in one step by a set-request with all necessary VPL parameter values and atmVplRowStatus set to createAndGo(4). In contrast to the negotiated VPL establishment which allows for detailed error checking (i.e., set errors are explicitly linked to particular resource acquisition failures), the one-shot VPL establishment performs the setup on one operation but does not have the advantage of step-wise error checking. VPL Retirement A VPL is released by setting atmVplRowStatus to destroy(6), and the agent may release all associated resources." INDEX {ifIndex, atmVplVpi } ::= { atmVplTable 1} AtmVplEntry ::= SEQUENCE { atmVplVpi AtmVpIdentifier, atmVplAdminStatus AtmVorXAdminStatus, atmVplOperStatus AtmVorXOperStatus, atmVplLastChange AtmVorXLastChange, atmVplReceiveTrafficDescrIndex AtmTrafficDescrParamIndex, atmVplTransmitTrafficDescrIndex AtmTrafficDescrParamIndex, atmVplCrossConnectIdentifier INTEGER, atmVplRowStatus RowStatus, atmVplCastType AtmConnCastType, atmVplConnKind AtmConnKind } atmVplVpi OBJECT-TYPE SYNTAX AtmVpIdentifier ACCESS read-only STATUS mandatory DESCRIPTION "The VPI value of the VPL." ::= { atmVplEntry 1} atmVplAdminStatus OBJECT-TYPE SYNTAX AtmVorXAdminStatus ACCESS read-only STATUS mandatory DESCRIPTION "This object is instanciated only for a VPL which terminates a VPC (i.e., one which is NOT cross-connected to other VPLs). Its value specifies the desired administrative state of the VPL." DEFVAL { down } ::= { atmVplEntry 2} atmVplOperStatus OBJECT-TYPE SYNTAX AtmVorXOperStatus ACCESS read-only STATUS mandatory DESCRIPTION "The current operational status of the VPL." ::= { atmVplEntry 3} atmVplLastChange OBJECT-TYPE SYNTAX AtmVorXLastChange ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime at the time this VPL entered its current operational state." ::= { atmVplEntry 4 } atmVplReceiveTrafficDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the receive direction of the VPL." DEFVAL { 0 } ::= { atmVplEntry 5} atmVplTransmitTrafficDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the transmit direction of the VPL." DEFVAL { 0 } ::= { atmVplEntry 6} atmVplCrossConnectIdentifier OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "This object is instantiated only for a VPL which is cross-connected to other VPLs that belong to the same VPC. All such associated VPLs have the same value of this object, and all their cross-connections are identified either by entries that are indexed by the same value of atmVpCrossConnectIndex in the atmVpCrossConnectTable of this MIB module or by the same value of the cross-connect index in the cross-connect table for SVCs and Soft PVCs (defined in a separate MIB module). At no time should entries in these respective cross-connect tables exist simultaneously with the same cross-connect index value. The value of this object is initialized by the agent after the associated entries in the atmVpCrossConnectTable have been created." ::= {atmVplEntry 7} atmVplRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This object is used to create, delete or modify a row in this table. To create a new VCL, this object is initially set to 'createAndWait' or 'createAndGo'. This object should not be set to 'active' unless the following columnar objects have been set to their desired value in this row: atmVplReceiveTrafficDescrIndex and atmVplTransmitTrafficDescrIndex. The DESCRIPTION of atmVplEntry provides further guidance to row treatment in this table." DEFVAL { active } ::= {atmVplEntry 8} atmVplCastType OBJECT-TYPE SYNTAX AtmConnCastType ACCESS read-only STATUS mandatory DESCRIPTION "The connection topology type." DEFVAL { p2p } ::= {atmVplEntry 9} atmVplConnKind OBJECT-TYPE SYNTAX AtmConnKind ACCESS read-only STATUS mandatory DESCRIPTION "The use of call control." DEFVAL { pvc } ::= {atmVplEntry 10} -- ATM Interface Virtual Channel Link (VCL) Table -- This table contains configuration and state -- information of a bi-directional Virtual Channel -- Link (VCL) at an ATM interface. -- This table can be used to create, delete or modify -- a VCL that is terminated in an ATM host or switch. -- This table can also be -- used to create, delete or modify a VCL that is -- cross-connected to another VCL. -- The ATM Interface VCL Table atmVclTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmVclEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Virtual Channel Link (VCL) table. A bi-directional VCL is modeled as one entry in this table. This table can be used for PVCs, SVCs and Soft PVCs." ::= { atmMIBObjects 7} atmVclEntry OBJECT-TYPE SYNTAX AtmVclEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the VCL table. This entry is used to model a bi-directional VCL. To create a VCL at an ATM interface, either of the following procedures are used: Negotiated VCL establishment (1) The management application creates a VCL entry in the atmVclTable by setting atmVclRowStatus to createAndWait(5). This may fail for the following reasons: - The selected VPI/VCI values are unavailable, - The selected VPI/VCI values are in use. Otherwise, the agent creates a row and reserves the VPI/VCI values on that port. (2) The manager selects an existing row(s) in the atmTrafficDescrParamTable, thereby, selecting a set of self-consistent ATM traffic parameters and the service category for receive and transmit directions of the VCL. (2a) If no suitable row(s) in the atmTrafficDescrParamTable exists, the manager must create a new row(s) in that table. (2b) The manager characterizes the VCL's traffic parameters through setting the atmVclReceiveTrafficDescrIndex and the atmVclTransmitTrafficDescrIndex values in the VCL table, which point to the rows containing desired ATM traffic parameter values in the atmTrafficDescrParamTable. The agent will check the availability of resources and may refuse the request. If the transmit and receive service categories are inconsistent, the agent should refuse the request. (3) The manager activates the VCL by setting the the atmVclRowStatus to active(1) (for requirements on this activation see the description of atmVclRowStatus). If this set is successful, the agent has reserved the resources to satisfy the requested traffic parameter values and the service category for that VCL. (4) If the VCL terminates a VCC in the ATM host or switch, the manager turns on the atmVclAdminStatus to up(1) to turn the VCL traffic flow on. Otherwise, the atmVcCrossConnectTable must be used to cross-connect the VCL to another VCL(s) in an ATM switch or network. One-Shot VCL Establishment A VCL may also be established in one step by a set-request with all necessary VCL parameter values and atmVclRowStatus set to createAndGo(4). In contrast to the negotiated VCL establishment which allows for detailed error checking (i.e., set errors are explicitly linked to particular resource acquisition failures), the one-shot VCL establishment performs the setup on one operation but does not have the advantage of step-wise error checking. VCL Retirement A VCL is released by setting atmVclRowStatus to destroy(6), and the agent may release all associated resources." INDEX {ifIndex, atmVclVpi, atmVclVci } ::= { atmVclTable 1} AtmVclEntry ::= SEQUENCE { atmVclVpi AtmVpIdentifier, atmVclVci AtmVcIdentifier, atmVclAdminStatus AtmVorXAdminStatus, atmVclOperStatus AtmVorXOperStatus, atmVclLastChange AtmVorXLastChange, atmVclReceiveTrafficDescrIndex AtmTrafficDescrParamIndex, atmVclTransmitTrafficDescrIndex AtmTrafficDescrParamIndex, atmVccAalType INTEGER, atmVccAal5CpcsTransmitSduSize INTEGER, atmVccAal5CpcsReceiveSduSize INTEGER, atmVccAal5EncapsType INTEGER, atmVclCrossConnectIdentifier INTEGER, atmVclRowStatus RowStatus, atmVclCastType AtmConnCastType, atmVclConnKind AtmConnKind } atmVclVpi OBJECT-TYPE SYNTAX AtmVpIdentifier ACCESS read-only STATUS mandatory DESCRIPTION "The VPI value of the VCL." ::= { atmVclEntry 1} atmVclVci OBJECT-TYPE SYNTAX AtmVcIdentifier ACCESS read-only STATUS mandatory DESCRIPTION "The VCI value of the VCL." ::= { atmVclEntry 2} atmVclAdminStatus OBJECT-TYPE SYNTAX AtmVorXAdminStatus ACCESS read-only STATUS mandatory DESCRIPTION "This object is instanciated only for a VCL which terminates a VCC (i.e., one which is NOT cross-connected to other VCLs). Its value specifies the desired administrative state of the VCL." DEFVAL { down } ::= { atmVclEntry 3} atmVclOperStatus OBJECT-TYPE SYNTAX AtmVorXOperStatus ACCESS read-only STATUS mandatory DESCRIPTION "The current operational status of the VCL." ::= { atmVclEntry 4} atmVclLastChange OBJECT-TYPE SYNTAX AtmVorXLastChange ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime at the time this VCL entered its current operational state." ::= { atmVclEntry 5 } atmVclReceiveTrafficDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCL." DEFVAL { 0 } ::= { atmVclEntry 6} atmVclTransmitTrafficDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VCL." DEFVAL { 0 } ::= { atmVclEntry 7} atmVccAalType OBJECT-TYPE SYNTAX INTEGER { aal1(1), aal34(2), aal5(3), other(4), unknown(5), aal2(6) } ACCESS read-only STATUS mandatory DESCRIPTION "An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL is in use. The type of AAL used on this VCC. The AAL type includes AAL1, AAL2, AAL3/4, and AAL5. The other(4) may be user-defined AAL type. The unknown type indicates that the AAL type cannot be determined." DEFVAL { aal5 } ::= { atmVclEntry 8 } atmVccAal5CpcsTransmitSduSize OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDU size in octets that is supported on the transmit direction of this VCC." DEFVAL { 9188 } ::= { atmVclEntry 9 } atmVccAal5CpcsReceiveSduSize OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDU size in octets that is supported on the receive direction of this VCC." DEFVAL { 9188 } ::= { atmVclEntry 10 } atmVccAal5EncapsType OBJECT-TYPE SYNTAX INTEGER { vcMultiplexRoutedProtocol(1), vcMultiplexBridgedProtocol8023(2), vcMultiplexBridgedProtocol8025(3), vcMultiplexBridgedProtocol8026(4), vcMultiplexLANemulation8023(5), vcMultiplexLANemulation8025(6), llcEncapsulation(7), multiprotocolFrameRelaySscs(8), other(9), unknown(10) } ACCESS read-only STATUS mandatory DESCRIPTION "An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The type of data encapsulation used over the AAL5 SSCS layer. The definitions reference RFC 1483 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification." DEFVAL { llcEncapsulation } ::= { atmVclEntry 11 } atmVclCrossConnectIdentifier OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "This object is instantiated only for a VCL which is cross-connected to other VCLs that belong to the same VCC. All such associated VCLs have the same value of this object, and all their cross-connections are identified either by entries that are indexed by the same value of atmVcCrossConnectIndex in the atmVcCrossConnectTable of this MIB module or by the same value of the cross-connect index in the cross-connect table for SVCs and Soft PVCs (defined in a separate MIB module). At no time should entries in these respective cross-connect tables exist simultaneously with the same cross-connect index value. The value of this object is initialized by the agent after the associated entries in the atmVcCrossConnectTable have been created." ::= {atmVclEntry 12} atmVclRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This object is used to create, delete or modify a row in this table. To create a new VCL, this object is initially set to 'createAndWait' or 'createAndGo'. This object should not be set to 'active' unless the following columnar objects have been set to their desired value in this row: atmVclReceiveTrafficDescrIndex, atmVclTransmitTrafficDescrIndex. In addition, if the local VCL end-point is also the VCC end-point: atmVccAalType. In addition, for AAL5 connections only: atmVccAal5CpcsTransmitSduSize, atmVccAal5CpcsReceiveSduSize, and atmVccAal5EncapsType. (The existence of these objects imply the AAL connection type.). The DESCRIPTION of atmVclEntry provides further guidance to row treatment in this table." DEFVAL { active } ::= {atmVclEntry 13} atmVclCastType OBJECT-TYPE SYNTAX AtmConnCastType ACCESS read-only STATUS mandatory DESCRIPTION "The connection topology type." DEFVAL { p2p } ::= {atmVclEntry 14} atmVclConnKind OBJECT-TYPE SYNTAX AtmConnKind ACCESS read-only STATUS mandatory DESCRIPTION "The use of call control." DEFVAL { pvc } ::= {atmVclEntry 15} -- ATM Virtual Path (VP) Cross Connect Table -- This table contains configuration and state -- information of point-to-point, -- point-to-multipoint, or multipoint-to-multipoint -- VP cross-connects for PVCs. -- This table has read-create access and can be used -- to cross-connect the VPLs together in an ATM switch -- or network. The atmVpCrossConnectIndex -- is used to associate the related -- VPLs that are cross-connected together. -- The ATM VP Cross Connect Table -- models each bi-directional VPC -- cross-connect as a set of entries in -- the atmVpCrossConnectTable. A -- point-to-point VPC cross-connect is modeled -- as one entry; a point-to-multipoint (N leafs) VPC -- cross-connect as N entries in this table; and -- a multipoint-to-multipoint (N parties) VPC cross- -- connect as N(N-1)/2 entries in this table. -- In the latter cases, all the N (or N(N-1)/2) entries -- are associated with a single VPC cross-connect by -- having the same value of atmVpCrossConnectIndex. -- _________________________________________ -- | | -- Low | ATM Switch or Network | High -- port| | port -- _____|>> from low to high VPC traffic flow >>|______ -- |<< from high to low VPC traffic flow <<| -- | | -- |_______________________________________| -- -- The terms low and high are chosen to represent -- numerical ordering of the two interfaces associated -- with a VPC cross-connect. That is, the ATM interface -- with the lower value of ifIndex is termed 'low', -- while the other ATM interface associated with the -- VPC cross-connect is termed 'high'. This terminology -- is used to provide directional information; for -- example, the atmVpCrossConnectL2HOperStatus applies -- to the low->high direction, and -- atmVpCrossConnectH2LOperStatus applies to the -- high->low direction, as illustrated above. -- atmVpCrossConnectIndexNext OBJECT-TYPE -- SYNTAX INTEGER (0..2147483647) -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "This object contains an appropriate value to -- be used for atmVpCrossConnectIndex when creating -- entries in the atmVpCrossConnectTable. The value -- 0 indicates that no unassigned entries are -- available. To obtain the atmVpCrossConnectIndex -- value for a new entry, the manager issues a -- management protocol retrieval operation to obtain -- the current value of this object. After each -- retrieval, the agent should modify the value to -- the next unassigned index. -- After a manager retrieves a value the agent will -- determine through its local policy when this index -- value will be made available for reuse." -- ::= { atmMIBObjects 8 } -- The ATM VP Cross Connect Table -- atmVpCrossConnectTable OBJECT-TYPE -- SYNTAX SEQUENCE OF AtmVpCrossConnectEntry -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "The ATM VP Cross Connect table for PVCs. -- An entry in this table models two -- cross-connected VPLs. -- Each VPL must have its atmConnKind set -- to pvc(1)." -- ::= { atmMIBObjects 9 } -- -- -- atmVpCrossConnectEntry OBJECT-TYPE -- SYNTAX AtmVpCrossConnectEntry -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "An entry in the ATM VP Cross Connect table. -- This entry is used to model a bi-directional -- ATM VP cross-connect which cross-connects -- two VPLs. -- -- Step-wise Procedures to set up a VP Cross-connect -- -- Once the entries in the atmVplTable are created, -- the following procedures are used -- to cross-connect the VPLs together. -- -- (1) The manager obtains a unique -- atmVpCrossConnectIndex by reading the -- atmVpCrossConnectIndexNext object. -- -- (2) Next, the manager creates a set of one -- or more rows in the ATM VP Cross Connect -- Table, one for each cross-connection between -- two VPLs. Each row is indexed by the ATM -- interface port numbers and VPI values of the -- two ends of that cross-connection. -- This set of rows specifies the topology of the -- VPC cross-connect and is identified by a single -- value of atmVpCrossConnectIndex. -- -- Negotiated VP Cross-Connect Establishment -- -- (2a) The manager creates a row in this table by -- setting atmVpCrossConnectRowStatus to -- createAndWait(5). The agent checks the -- requested topology and the mutual sanity of -- the ATM traffic parameters and -- service categories, i.e., the row creation -- fails if: -- - the requested topology is incompatible with -- associated values of atmVplCastType, -- - the requested topology is not supported -- by the agent, -- - the traffic/service category parameter values -- associated with the requested row are -- incompatible with those of already existing -- rows for this VP cross-connect. -- [For example, for setting up -- a point-to-point VP cross-connect, the -- ATM traffic parameters in the receive direction -- of a VPL at the low end of the cross-connect -- must equal to the traffic parameters in the -- transmit direction of the other VPL at the -- high end of the cross-connect, -- otherwise, the row creation fails.] -- The agent also checks for internal errors -- in building the cross-connect. -- -- The atmVpCrossConnectIndex values in the -- corresponding atmVplTable rows are filled -- in by the agent at this point. -- -- (2b) The manager promotes the row in the -- atmVpCrossConnectTable by setting -- atmVpCrossConnectRowStatus to active(1). If -- this set is successful, the agent has reserved -- the resources specified by the ATM traffic -- parameter and Service category values -- for each direction of the VP cross-connect -- in an ATM switch or network. -- -- (3) The manager sets the -- atmVpCrossConnectAdminStatus to up(1) in all -- rows of this VP cross-connect to turn the -- traffic flow on. -- -- -- One-Shot VP Cross-Connect Establishment -- -- A VP cross-connect may also be established in -- one step by a set-request with all necessary -- parameter values and atmVpCrossConnectRowStatus -- set to createAndGo(4). -- -- In contrast to the negotiated VP cross-connect -- establishment which allows for detailed error -- checking (i.e., set errors are explicitly linked -- to particular resource acquisition failures), -- the one-shot VP cross-connect establishment -- performs the setup on one operation but does not -- have the advantage of step-wise error checking. -- -- VP Cross-Connect Retirement -- -- A VP cross-connect identified by a particular -- value of atmVpCrossConnectIndex is released by: -- -- (1) Setting atmVpCrossConnectRowStatus of all -- rows identified by this value of -- atmVpCrossConnectIndex to destroy(6). -- The agent may release all -- associated resources, and the -- atmVpCrossConnectIndex values in the -- corresponding atmVplTable row are removed. -- Note that a situation when only a subset of -- the associated rows are deleted corresponds -- to a VP topology change. -- -- (2) After deletion of the appropriate -- atmVpCrossConnectEntries, the manager may -- set atmVplRowStatus to destroy(6) the -- associated VPLs. The agent releases -- the resources and removes the associated -- rows in the atmVplTable. -- -- VP Cross-connect Reconfiguration -- -- At the discretion of the agent, a VP -- cross-connect may be reconfigured by -- adding and/or deleting leafs to/from -- the VP topology as per the VP cross-connect -- establishment/retirement procedures. -- Reconfiguration of traffic/service category parameter -- values requires release of the VP cross-connect -- before those parameter values may by changed -- for individual VPLs." -- INDEX { atmVpCrossConnectIndex, -- atmVpCrossConnectLowIfIndex, -- atmVpCrossConnectLowVpi, -- atmVpCrossConnectHighIfIndex, -- atmVpCrossConnectHighVpi } -- ::= { atmVpCrossConnectTable 1 } -- -- AtmVpCrossConnectEntry ::= SEQUENCE { -- atmVpCrossConnectIndex INTEGER, -- atmVpCrossConnectLowIfIndex InterfaceIndex, -- atmVpCrossConnectLowVpi AtmVpIdentifier, -- atmVpCrossConnectHighIfIndex InterfaceIndex, -- atmVpCrossConnectHighVpi AtmVpIdentifier, -- atmVpCrossConnectAdminStatus AtmVorXAdminStatus, -- atmVpCrossConnectL2HOperStatus AtmVorXOperStatus, -- atmVpCrossConnectH2LOperStatus AtmVorXOperStatus, -- atmVpCrossConnectL2HLastChange AtmVorXLastChange, -- atmVpCrossConnectH2LLastChange AtmVorXLastChange, -- atmVpCrossConnectRowStatus RowStatus -- } -- -- atmVpCrossConnectIndex OBJECT-TYPE -- SYNTAX INTEGER (1..2147483647) -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "A unique value to identify this VP cross-connect. -- For each VPL associated with this cross-connect, -- the agent reports this cross-connect index value -- in the atmVplCrossConnectIdentifier attribute of -- the corresponding atmVplTable entries." -- ::= { atmVpCrossConnectEntry 1 } -- -- atmVpCrossConnectLowIfIndex OBJECT-TYPE -- SYNTAX InterfaceIndex -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The ifIndex value of the ATM interface for -- this VP cross-connect. The term low implies -- that this ATM interface has the numerically lower -- ifIndex value than the other ATM interface -- identified in the same atmVpCrossConnectEntry." -- ::= { atmVpCrossConnectEntry 2 } -- -- atmVpCrossConnectLowVpi OBJECT-TYPE -- SYNTAX AtmVpIdentifier -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The VPI value at the ATM interface -- associated with the VP cross-connect that is -- identified by atmVpCrossConnectLowIfIndex." -- ::= { atmVpCrossConnectEntry 3 } -- -- atmVpCrossConnectHighIfIndex OBJECT-TYPE -- SYNTAX InterfaceIndex -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The ifIndex value of the ATM interface for -- this VP cross-connect. The term high implies that -- this ATM interface has the numerically higher -- ifIndex value than the other ATM interface -- identified in the same atmVpCrossConnectEntry." -- ::= { atmVpCrossConnectEntry 4 } -- -- atmVpCrossConnectHighVpi OBJECT-TYPE -- SYNTAX AtmVpIdentifier -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The VPI value at the ATM interface -- associated with the VP cross-connect that is -- identified by atmVpCrossConnectHighIfIndex." -- ::= { atmVpCrossConnectEntry 5 } -- -- atmVpCrossConnectAdminStatus OBJECT-TYPE -- SYNTAX AtmVorXAdminStatus -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The desired administrative status of this -- bi-directional VP cross-connect." -- DEFVAL { down } -- ::= { atmVpCrossConnectEntry 6 } -- -- atmVpCrossConnectL2HOperStatus OBJECT-TYPE -- SYNTAX AtmVorXOperStatus -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The operational status of the VP cross-connect -- in one direction; (i.e., from the low to -- high direction)." -- ::= { atmVpCrossConnectEntry 7 } -- -- atmVpCrossConnectH2LOperStatus OBJECT-TYPE -- SYNTAX AtmVorXOperStatus -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The operational status of the VP cross-connect -- in one direction; (i.e., from the high to -- low direction)." -- ::= { atmVpCrossConnectEntry 8 } -- -- atmVpCrossConnectL2HLastChange OBJECT-TYPE -- SYNTAX AtmVorXLastChange -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The value of sysUpTime at the time this -- VP cross-connect entered its current operational -- state in the low to high direction." -- ::= { atmVpCrossConnectEntry 9 } -- -- atmVpCrossConnectH2LLastChange OBJECT-TYPE -- SYNTAX AtmVorXLastChange -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The value of sysUpTime at the time this -- VP cross-connect entered its current operational -- in the high to low direction." -- ::= { atmVpCrossConnectEntry 10 } -- -- atmVpCrossConnectRowStatus OBJECT-TYPE -- SYNTAX RowStatus -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The status of this entry in the -- atmVpCrossConnectTable. This object is used to -- create a cross-connect for cross-connecting -- VPLs which are created using the atmVplTable -- or to change or delete an existing cross-connect. -- This object must be initially set -- to `createAndWait' or 'createAndGo'. -- To turn on a VP cross-connect, -- the atmVpCrossConnectAdminStatus -- is set to `up'." -- DEFVAL { active } -- ::= { atmVpCrossConnectEntry 11 } -- -- -- ATM Virtual Channel (VC) Cross Connect Table -- This table contains configuration and state -- information of point-to-point, -- point-to-multipoint or multipoint-to-multipoint -- VC cross-connects for PVCs. -- This table has read-create access and is used -- to cross-connect the VCLs together in an ATM switch -- or network that belong to a VC connection. -- The atmVcCrossConnectIndex is used to associate -- the related VCLs that are cross-connected together. -- The model using step-wise procedures described for setting -- up a VP cross-connect is also used for setting up -- a VC cross-connect. -- atmVcCrossConnectIndexNext OBJECT-TYPE -- SYNTAX INTEGER (0..2147483647) -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "This object contains an appropriate value to -- be used for atmVcCrossConnectIndex when creating -- entries in the atmVcCrossConnectTable. The value -- 0 indicates that no unassigned entries are -- available. To obtain the atmVcCrossConnectIndex -- value for a new entry, the manager issues a -- management protocol retrieval operation to obtain -- the current value of this object. After each -- retrieval, the agent should modify the value to -- the next unassigned index. -- After a manager retrieves a value the agent will -- determine through its local policy when this index -- value will be made available for reuse." -- ::= { atmMIBObjects 10 } -- The ATM VC Cross Connect Table -- atmVcCrossConnectTable OBJECT-TYPE -- SYNTAX SEQUENCE OF AtmVcCrossConnectEntry -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "The ATM VC Cross Connect table for PVCs. -- An entry in this table models two -- cross-connected VCLs. -- Each VCL must have its atmConnKind set -- to pvc(1)." -- ::= { atmMIBObjects 11 } -- -- -- atmVcCrossConnectEntry OBJECT-TYPE -- SYNTAX AtmVcCrossConnectEntry -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "An entry in the ATM VC Cross Connect table. -- This entry is used to model a bi-directional ATM -- VC cross-connect cross-connecting two end points. -- Step-wise Procedures to set up a VC Cross-connect -- Once the entries in the atmVclTable are created, -- the following procedures are used -- to cross-connect the VCLs together to -- form a VCC segment. -- -- (1) The manager obtains a unique -- atmVcCrossConnectIndex by reading the -- atmVcCrossConnectIndexNext object. -- -- (2) Next, the manager creates a set of one -- or more rows in the ATM VC Cross Connect -- Table, one for each cross-connection between -- two VCLs. Each row is indexed by the ATM -- interface port numbers and VPI/VCI values of -- the two ends of that cross-connection. -- This set of rows specifies the topology of the -- VCC cross-connect and is identified by a single -- value of atmVcCrossConnectIndex. -- -- Negotiated VC Cross-Connect Establishment -- -- (2a) The manager creates a row in this table by -- setting atmVcCrossConnectRowStatus to -- createAndWait(5). The agent checks the -- requested topology and the mutual sanity of -- the ATM traffic parameters and -- service categories, i.e., the row creation -- fails if: -- - the requested topology is incompatible with -- associated values of atmVclCastType, -- - the requested topology is not supported -- by the agent, -- - the traffic/service category parameter values -- associated with the requested row are -- incompatible with those of already existing -- rows for this VC cross-connect. -- [For example, for setting up -- a point-to-point VC cross-connect, the -- ATM traffic parameters in the receive direction -- of a VCL at the low end of the cross-connect -- must equal to the traffic parameters in the -- transmit direction of the other VCL at the -- high end of the cross-connect, -- otherwise, the row creation fails.] -- The agent also checks for internal errors -- in building the cross-connect. -- -- The atmVcCrossConnectIndex values in the -- corresponding atmVclTable rows are filled -- in by the agent at this point. -- -- (2b) The manager promotes the row in the -- atmVcCrossConnectTable by setting -- atmVcCrossConnectRowStatus to active(1). If -- this set is successful, the agent has reserved -- the resources specified by the ATM traffic -- parameter and Service category values -- for each direction of the VC cross-connect -- in an ATM switch or network. -- -- (3) The manager sets the -- atmVcCrossConnectAdminStatus to up(1) -- in all rows of this VC cross-connect to -- turn the traffic flow on. -- -- -- One-Shot VC Cross-Connect Establishment -- -- A VC cross-connect may also be established in -- one step by a set-request with all necessary -- parameter values and atmVcCrossConnectRowStatus -- set to createAndGo(4). -- -- In contrast to the negotiated VC cross-connect -- establishment which allows for detailed error -- checking i.e., set errors are explicitly linked to -- particular resource acquisition failures), the -- one-shot VC cross-connect establishment -- performs the setup on one operation but does -- not have the advantage of step-wise error -- checking. -- -- VC Cross-Connect Retirement -- -- A VC cross-connect identified by a particular -- value of atmVcCrossConnectIndex is released by: -- -- (1) Setting atmVcCrossConnectRowStatus of all rows -- identified by this value of -- atmVcCrossConnectIndex to destroy(6). -- The agent may release all -- associated resources, and the -- atmVcCrossConnectIndex values in the -- corresponding atmVclTable row are removed. -- Note that a situation when only a subset of -- the associated rows are deleted corresponds -- to a VC topology change. -- -- (2) After deletion of the appropriate -- atmVcCrossConnectEntries, the manager may -- set atmVclRowStatus to destroy(6) the -- associated VCLs. The agent releases -- the resources and removes the associated -- rows in the atmVclTable. -- -- VC Cross-Connect Reconfiguration -- -- At the discretion of the agent, a VC -- cross-connect may be reconfigured by -- adding and/or deleting leafs to/from -- the VC topology as per the VC cross-connect -- establishment/retirement procedures. -- Reconfiguration of traffic/service category parameter -- values requires release of the VC cross-connect -- before those parameter values may by changed -- for individual VCLs." -- INDEX { atmVcCrossConnectIndex, -- atmVcCrossConnectLowIfIndex, -- atmVcCrossConnectLowVpi, -- atmVcCrossConnectLowVci, -- atmVcCrossConnectHighIfIndex, -- atmVcCrossConnectHighVpi, -- atmVcCrossConnectHighVci } -- ::= { atmVcCrossConnectTable 1 } -- -- AtmVcCrossConnectEntry ::= SEQUENCE { -- atmVcCrossConnectIndex INTEGER, -- atmVcCrossConnectLowIfIndex InterfaceIndex, -- atmVcCrossConnectLowVpi AtmVpIdentifier, -- atmVcCrossConnectLowVci AtmVcIdentifier, -- atmVcCrossConnectHighIfIndex InterfaceIndex, -- atmVcCrossConnectHighVpi AtmVpIdentifier, -- atmVcCrossConnectHighVci AtmVcIdentifier, -- atmVcCrossConnectAdminStatus AtmVorXAdminStatus, -- atmVcCrossConnectL2HOperStatus AtmVorXOperStatus, -- atmVcCrossConnectH2LOperStatus AtmVorXOperStatus, -- atmVcCrossConnectL2HLastChange AtmVorXLastChange, -- atmVcCrossConnectH2LLastChange AtmVorXLastChange, -- atmVcCrossConnectRowStatus RowStatus -- } -- -- atmVcCrossConnectIndex OBJECT-TYPE -- SYNTAX INTEGER (1..2147483647) -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "A unique value to identify this VC cross-connect. -- For each VCL associated with this cross-connect, -- the agent reports this cross-connect index value -- in the atmVclCrossConnectIdentifier attribute of -- the corresponding atmVclTable entries." -- ::= { atmVcCrossConnectEntry 1 } -- -- atmVcCrossConnectLowIfIndex OBJECT-TYPE -- SYNTAX InterfaceIndex -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The ifIndex value of the ATM interface for this -- VC cross-connect. The term low implies -- that this ATM interface has the numerically lower -- ifIndex value than the other ATM interface -- identified in the same atmVcCrossConnectEntry." -- ::= { atmVcCrossConnectEntry 2 } -- -- atmVcCrossConnectLowVpi OBJECT-TYPE -- SYNTAX AtmVpIdentifier -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The VPI value at the ATM interface -- associated with the VC cross-connect that is -- identified by atmVcCrossConnectLowIfIndex." -- ::= { atmVcCrossConnectEntry 3 } -- -- atmVcCrossConnectLowVci OBJECT-TYPE -- SYNTAX AtmVcIdentifier -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The VCI value at the ATM interface -- associated with this VC cross-connect that is -- identified by atmVcCrossConnectLowIfIndex." -- ::= { atmVcCrossConnectEntry 4 } -- -- atmVcCrossConnectHighIfIndex OBJECT-TYPE -- SYNTAX InterfaceIndex -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The ifIndex value for the ATM interface for -- this VC cross-connect. The term high implies -- that this ATM interface has the numerically higher -- ifIndex value than the other ATM interface -- identified in the same atmVcCrossConnectEntry." -- ::= { atmVcCrossConnectEntry 5 } -- -- atmVcCrossConnectHighVpi OBJECT-TYPE -- SYNTAX AtmVpIdentifier -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The VPI value at the ATM interface -- associated with the VC cross-connect that is -- identified by atmVcCrossConnectHighIfIndex." -- ::= { atmVcCrossConnectEntry 6 } -- -- atmVcCrossConnectHighVci OBJECT-TYPE -- SYNTAX AtmVcIdentifier -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The VCI value at the ATM interface -- associated with the VC cross-connect that is -- identified by atmVcCrossConnectHighIfIndex." -- ::= { atmVcCrossConnectEntry 7 } -- -- atmVcCrossConnectAdminStatus OBJECT-TYPE -- SYNTAX AtmVorXAdminStatus -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The desired administrative status of this -- bi-directional VC cross-connect." -- DEFVAL { down } -- ::= { atmVcCrossConnectEntry 8 } -- -- atmVcCrossConnectL2HOperStatus OBJECT-TYPE -- SYNTAX AtmVorXOperStatus -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The current operational status of the -- VC cross-connect in one direction; (i.e., -- from the low to high direction)." -- ::= { atmVcCrossConnectEntry 9 } -- -- -- atmVcCrossConnectH2LOperStatus OBJECT-TYPE -- SYNTAX AtmVorXOperStatus -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The current operational status of the -- VC cross-connect in one direction; (i.e., -- from the high to low direction)." -- ::= { atmVcCrossConnectEntry 10 } -- -- atmVcCrossConnectL2HLastChange OBJECT-TYPE -- SYNTAX AtmVorXLastChange -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The value of sysUpTime at the time this -- VC cross-connect entered its current -- operational state in low to high direction." -- ::= { atmVcCrossConnectEntry 11 } -- -- atmVcCrossConnectH2LLastChange OBJECT-TYPE -- SYNTAX AtmVorXLastChange -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The value of sysUpTime at the time this -- VC cross-connect entered its current -- operational state in high to low direction." -- ::= { atmVcCrossConnectEntry 12 } -- -- atmVcCrossConnectRowStatus OBJECT-TYPE -- SYNTAX RowStatus -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The status of this entry in the -- atmVcCrossConnectTable. This object is used to -- create a new cross-connect for cross-connecting -- VCLs which are created using the atmVclTable -- or to change or delete existing cross-connect. -- This object must be initially set to -- `createAndWait' or 'createAndGo'. -- To turn on a VC cross-connect, -- the atmVcCrossConnectAdminStatus -- is set to `up'." -- DEFVAL { active } -- ::= { atmVcCrossConnectEntry 13 } -- -- -- AAL5 Virtual Channel Connection Performance Statistics -- Table -- This table contains the AAL5 -- performance statistics of a VCC at the -- interface associated with an AAL5 entity in an ATM -- host or ATM switch. aal5VccTable OBJECT-TYPE SYNTAX SEQUENCE OF Aal5VccEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains AAL5 VCC performance parameters." ::= { atmMIBObjects 12 } aal5VccEntry OBJECT-TYPE SYNTAX Aal5VccEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains the AAL5 VCC performance parameters and is indexed by ifIndex values of AAL5 interfaces and the associated VPI/VCI values." INDEX { ifIndex, aal5VccVpi, aal5VccVci } ::= { aal5VccTable 1 } Aal5VccEntry ::= SEQUENCE { aal5VccVpi AtmVpIdentifier, aal5VccVci AtmVcIdentifier, aal5VccCrcErrors Counter32, aal5VccSarTimeOuts Counter32, aal5VccOverSizedSDUs Counter32 } aal5VccVpi OBJECT-TYPE SYNTAX AtmVpIdentifier ACCESS read-only STATUS mandatory DESCRIPTION "The VPI value of the AAL5 VCC at the interface identified by the ifIndex." ::= { aal5VccEntry 1 } aal5VccVci OBJECT-TYPE SYNTAX AtmVcIdentifier ACCESS read-only STATUS mandatory DESCRIPTION "The VCI value of the AAL5 VCC at the interface identified by the ifIndex." ::= { aal5VccEntry 2 } aal5VccCrcErrors OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL5 CPCS PDUs received with CRC-32 errors on this AAL5 VCC at the interface associated with an AAL5 entity." ::= { aal5VccEntry 3 } aal5VccSarTimeOuts OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of partially re-assembled AAL5 CPCS PDUs which were discarded on this AAL5 VCC at the interface associated with an AAL5 entity because they were not fully re-assembled within the required time period. If the re-assembly timer is not supported, then this object contains a zero value." ::= { aal5VccEntry 4 } aal5VccOverSizedSDUs OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL5 CPCS PDUs discarded on this AAL5 VCC at the interface associated with an AAL5 entity because the AAL5 SDUs were too large." ::= { aal5VccEntry 5 } -- -- The following object may be used in conjunction with -- the atmTrafficDescrParamTable for the creation of -- new table entries. -- -- atmTrafficDescrParamIndexNext OBJECT-TYPE -- SYNTAX INTEGER (0..2147483647) -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "This object contains an appropriate value to -- be used for atmTrafficDescrParamIndex when -- creating entries in the -- atmTrafficDescrParamTable. -- The value 0 indicates that no unassigned -- entries are available. To obtain the -- atmTrafficDescrParamIndex value for a new -- entry, the manager issues a management -- protocol retrieval operation to obtain the -- current value of this object. After each -- retrieval, the agent should modify the value -- to the next unassigned index. -- After a manager retrieves a value the agent will -- determine through its local policy when this index -- value will be made available for reuse." -- ::= { atmMIBObjects 13 } -- Conformance Information atmMIBConformance OBJECT IDENTIFIER ::= { atmMIB 2 } atmMIBGroups OBJECT IDENTIFIER ::= { atmMIBConformance 1 } atmMIBCompliances OBJECT IDENTIFIER ::= { atmMIBConformance 2 } -- Compliance Statements -- atmMIBCompliance2 MODULE-COMPLIANCE -- STATUS mandatory -- DESCRIPTION -- "The compliance statement for SNMP entities -- including networks which have ATM and -- AAL5 interfaces." -- -- MODULE -- this module -- -- ****** Interface and Traffic Descriptor Support *** -- -- MANDATORY-GROUPS {atmInterfaceConfGroup2, -- atmTrafficDescrGroup2 } -- -- OBJECT atmInterfaceMaxVpcs -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceMaxVccs -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceMaxActiveVpiBits -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required. -- At the ATM UNI the maximum number of -- active VPI bits configured for use ranges -- from 0 to 8 only. -- Implementations may support smaller ranges." -- OBJECT atmInterfaceMaxActiveVciBits -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required. -- Implementations may support smaller ranges." -- -- OBJECT atmInterfaceIlmiVpi -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceIlmiVci -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceMyNeighborIpAddress -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceMyNeighborIfName -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceSubscrAddress -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParamIndexNext -- DESCRIPTION -- "This object is only required for systems -- that support the creation of entries in -- the atmTrafficDescrParamTable." -- -- OBJECT atmTrafficDescrType -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam1 -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam2 -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam3 -- MIN-ACCESS read-only ---- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam4 -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam5 -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmServiceCategory -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrRowStatus -- SYNTAX INTEGER {active(1)} -- -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- OBJECT atmTrafficFrameDiscard -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- -- -- -- ****** DS3 PLCP Support ************************** -- -- -- GROUP atmInterfaceDs3PlcpGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement the -- DS3 PLCP layer." -- -- -- -- ****** TC Sublayer Support ******************************** -- -- -- GROUP atmInterfaceTCGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement the -- TC Sublayer." -- -- -- -- -- ****** VPC Support ******************************* -- -- -- GROUP atmVpcTerminationGroup2 -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VPLs that terminate VPCs (i.e., ones which -- are NOT cross-connected to other VPLs)." ---- -- GROUP atmVplCrossConnectGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VPLs that are not associated with VCLs -- and are cross-connected to other VPLs -- for VPCs." -- -- GROUP atmVpPvcCrossConnectGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VPLs that are not associated with VCLs -- and are cross-connected to other VPLs -- for permanent VPCs (i.e., PVCs). -- This group is not used to crossconnect -- a PVC with an SVC to form a Soft PVC." -- -- OBJECT atmVplAdminStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVplReceiveTrafficDescrIndex -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVplTransmitTrafficDescrIndex -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVplRowStatus -- SYNTAX INTEGER {active(1)} -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- OBJECT atmVplCastType -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVplConnKind -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVpCrossConnectAdminStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVpCrossConnectRowStatus -- SYNTAX INTEGER {active(1)} -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- -- -- -- ****** VCC Support ******************************* -- -- -- GROUP atmVccTerminationGroup2 -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VCLs that terminate VCCs (i.e., ones which -- are NOT cross-connected to other VCLs)." -- -- GROUP atmVclCrossConnectGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VCLs that are cross-connected to other VCLs -- for VCCs." -- -- GROUP atmVcPvcCrossConnectGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VCLs that are cross-connected to other -- VCLs for permanent VCCs (i.e., PVCs). -- This group is not used to crossconnect -- a PVC with an SVC to form a Soft PVC." -- -- OBJECT atmVclAdminStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVclReceiveTrafficDescrIndex -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- OBJECT atmVclTransmitTrafficDescrIndex -- MIN-ACCESS read-only -- DESCRIPTION ---- "Write access is not required." -- -- OBJECT atmVccAalType -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVclRowStatus -- SYNTAX INTEGER {active(1)} -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- OBJECT atmVclCastType -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVclConnKind -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVcCrossConnectAdminStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVcCrossConnectRowStatus -- SYNTAX INTEGER { active(1)} -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- ****** AAL5 Support ****************************** -- -- GROUP aal5VccGroup -- DESCRIPTION -- "This group is mandatory for the -- AAL5 virtual connections only." -- OBJECT atmVccAal5CpcsTransmitSduSize -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVccAal5CpcsReceiveSduSize -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVccAal5EncapsType -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- ::= { atmMIBCompliances 2 } -- -- -- -- Units of Conformance -- -- atmInterfaceDs3PlcpGroup OBJECT-GROUP -- OBJECTS {atmInterfaceDs3PlcpSEFSs, -- atmInterfaceDs3PlcpAlarmState, -- atmInterfaceDs3PlcpUASs} -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing information -- about DS3 PLCP layer at an ATM interface." -- ::= { atmMIBGroups 3 } -- -- atmInterfaceTCGroup OBJECT-GROUP -- OBJECTS { atmInterfaceOCDEvents, -- atmInterfaceTCAlarmState } -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing information -- about TC sublayer at an ATM interface." -- ::= { atmMIBGroups 4 } -- -- aal5VccGroup OBJECT-GROUP -- OBJECTS {atmVccAal5CpcsTransmitSduSize, -- atmVccAal5CpcsReceiveSduSize, -- atmVccAal5EncapsType, -- aal5VccCrcErrors, aal5VccSarTimeOuts, -- aal5VccOverSizedSDUs } -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing -- AAL5 configuration and performance statistics -- of a VCC." -- ::= { atmMIBGroups 9 } -- -- atmInterfaceConfGroup2 OBJECT-GROUP -- OBJECTS { -- atmInterfaceMaxVpcs, atmInterfaceMaxVccs, -- atmInterfaceConfVpcs, atmInterfaceConfVccs, -- atmInterfaceMaxActiveVpiBits, -- atmInterfaceMaxActiveVciBits, -- atmInterfaceIlmiVpi, -- atmInterfaceIlmiVci, -- atmInterfaceMyNeighborIpAddress, -- atmInterfaceMyNeighborIfName, -- atmInterfaceCurrentMaxVpiBits, -- atmInterfaceCurrentMaxVciBits, -- atmInterfaceSubscrAddress } ---- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing configuration -- information about an ATM interface." -- ::= { atmMIBGroups 10 } -- -- atmTrafficDescrGroup2 OBJECT-GROUP -- OBJECTS { -- atmTrafficDescrType, atmTrafficDescrParam1, -- atmTrafficDescrParam2, atmTrafficDescrParam3, -- atmTrafficDescrParam4, atmTrafficDescrParam5, -- atmTrafficDescrRowStatus, atmServiceCategory, -- atmTrafficFrameDiscard, -- atmTrafficDescrParamIndexNext } -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing information -- about ATM traffic descriptor type and -- the associated parameters." -- ::= { atmMIBGroups 11 } -- -- atmVpcTerminationGroup2 OBJECT-GROUP -- OBJECTS {atmVplOperStatus, atmVplAdminStatus, -- atmVplLastChange, -- atmVplReceiveTrafficDescrIndex, -- atmVplTransmitTrafficDescrIndex, -- atmVplRowStatus, atmVplCastType, -- atmVplConnKind } -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing information -- about a VPL at an ATM interface which -- terminates a VPC (i.e., one which is NOT -- cross-connected to other VPLs)." -- ::= { atmMIBGroups 12 } -- -- atmVccTerminationGroup2 OBJECT-GROUP -- OBJECTS {atmVclOperStatus, atmVclAdminStatus, -- atmVclLastChange, -- atmVclReceiveTrafficDescrIndex, -- atmVclTransmitTrafficDescrIndex, -- atmVccAalType, atmVclRowStatus, -- atmVclCastType, atmVclConnKind } -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing information -- about a VCL at an ATM interface -- which terminates a VCC (i.e., one which is -- NOT cross-connected to other VCLs)." -- ::= { atmMIBGroups 13 } -- -- atmVplCrossConnectGroup OBJECT-GROUP -- OBJECTS { atmVplReceiveTrafficDescrIndex, -- atmVplTransmitTrafficDescrIndex, -- atmVplOperStatus, atmVplLastChange, -- atmVplRowStatus, -- atmVplCastType, atmVplConnKind } -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing -- information about the VPLs that -- are cross-connected together." -- ::= { atmMIBGroups 14 } -- -- atmVpPvcCrossConnectGroup OBJECT-GROUP -- OBJECTS { atmVpCrossConnectAdminStatus, -- atmVpCrossConnectL2HOperStatus, -- atmVpCrossConnectH2LOperStatus, -- atmVpCrossConnectL2HLastChange, -- atmVpCrossConnectH2LLastChange, -- atmVpCrossConnectRowStatus, -- atmVplCrossConnectIdentifier, -- atmVpCrossConnectIndexNext } -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing -- information about a VP cross-connect -- for PVCs. These objects are not used -- for Soft PVCs or SVCs." -- ::= { atmMIBGroups 15 } -- -- atmVclCrossConnectGroup OBJECT-GROUP -- OBJECTS { atmVclReceiveTrafficDescrIndex, -- atmVclTransmitTrafficDescrIndex, -- atmVclOperStatus, atmVclLastChange, -- atmVclRowStatus, -- atmVclCastType, atmVclConnKind } -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing -- information about the VCLs that -- are cross-connected together." -- ::= { atmMIBGroups 16 } -- -- atmVcPvcCrossConnectGroup OBJECT-GROUP -- OBJECTS { atmVcCrossConnectAdminStatus, -- atmVcCrossConnectL2HOperStatus, -- atmVcCrossConnectH2LOperStatus, -- atmVcCrossConnectL2HLastChange, -- atmVcCrossConnectH2LLastChange, -- atmVcCrossConnectRowStatus, -- atmVclCrossConnectIdentifier, -- atmVcCrossConnectIndexNext } -- STATUS mandatory -- DESCRIPTION -- "A collection of objects providing -- information about a VC cross-connect -- for PVCs. These objects are not used -- for Soft PVCs or SVCs." -- ::= { atmMIBGroups 17 } -- -- -- Deprecated Definitions - Objects -- atmInterfaceAddressType -- atmTrafficQoSClass -- Deprecated Definitions - Compliance -- atmMIBCompliance MODULE-COMPLIANCE -- STATUS deprecated -- DESCRIPTION -- "The compliance statement for SNMP entities -- including networks which have ATM and -- AAL5 interfaces." -- -- MODULE -- this module -- MANDATORY-GROUPS {atmInterfaceConfGroup, -- atmTrafficDescrGroup} -- -- OBJECT atmInterfaceMaxVpcs -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceMaxVccs -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceMaxActiveVpiBits -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceMaxActiveVciBits -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceIlmiVpi -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceIlmiVci -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceMyNeighborIpAddress -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmInterfaceMyNeighborIfName -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrType -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam1 -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam2 -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam3 -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam4 -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrParam5 -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficQoSClass -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmTrafficDescrRowStatus -- SYNTAX INTEGER {active(1)} -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- GROUP atmInterfaceDs3PlcpGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement the -- DS3 PLCP layer." -- -- GROUP atmInterfaceTCGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement the -- TC Sublayer." -- -- GROUP atmVpcTerminationGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VPLs that terminate VPCs (i.e., ones which -- are NOT cross-connected to other VPLs)." -- -- GROUP atmVpCrossConnectGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VPLs that are not associated with VCLs -- and are cross-connected to other VPLs." -- -- OBJECT atmVplAdminStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVplReceiveTrafficDescrIndex -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVplTransmitTrafficDescrIndex -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVplRowStatus -- SYNTAX INTEGER {active(1)} -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- OBJECT atmVpCrossConnectAdminStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVpCrossConnectRowStatus -- SYNTAX INTEGER {active(1)} -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- GROUP atmVccTerminationGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VCLs that terminate VCCs (i.e., ones which -- are NOT cross-connected to other VCLs)." -- -- GROUP atmVcCrossConnectGroup -- DESCRIPTION -- "This group is mandatory only for those -- ATM interfaces which implement ATM -- VCLs that are cross-connected to -- other VCLs." -- -- OBJECT atmVclAdminStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVclReceiveTrafficDescrIndex -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVclTransmitTrafficDescrIndex -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVccAalType -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVclRowStatus -- SYNTAX INTEGER {active(1)} -- -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- OBJECT atmVcCrossConnectAdminStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVcCrossConnectRowStatus -- SYNTAX INTEGER { active(1)} -- -- subset of RowStatus -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required, and only one -- of the six enumerated values for the -- RowStatus textual convention need be -- supported, specifically: active(1)." -- -- GROUP aal5VccGroup -- DESCRIPTION -- "This group is mandatory for the -- AAL5 virtual connections only." -- -- OBJECT atmVccAal5CpcsTransmitSduSize -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVccAal5CpcsReceiveSduSize -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- -- OBJECT atmVccAal5EncapsType -- MIN-ACCESS read-only -- DESCRIPTION -- "Write access is not required." -- ::= { atmMIBCompliances 1 } -- -- --* Deprecated Definitions - Groups --* -- atmInterfaceConfGroup OBJECT-GROUP -- OBJECTS { -- atmInterfaceMaxVpcs, atmInterfaceMaxVccs, -- atmInterfaceConfVpcs, atmInterfaceConfVccs, -- atmInterfaceMaxActiveVpiBits, -- atmInterfaceMaxActiveVciBits, -- atmInterfaceIlmiVpi, -- atmInterfaceIlmiVci, -- atmInterfaceAddressType, -- atmInterfaceAdminAddress, -- atmInterfaceMyNeighborIpAddress, -- atmInterfaceMyNeighborIfName } -- STATUS deprecated -- DESCRIPTION -- "A collection of objects providing configuration -- information about an ATM interface." -- ::= { atmMIBGroups 1 } -- -- atmTrafficDescrGroup OBJECT-GROUP -- OBJECTS { -- atmTrafficDescrType, atmTrafficDescrParam1, -- atmTrafficDescrParam2, atmTrafficDescrParam3, -- atmTrafficDescrParam4, atmTrafficDescrParam5, -- atmTrafficQoSClass, atmTrafficDescrRowStatus} -- STATUS deprecated -- DESCRIPTION -- "A collection of objects providing information -- about ATM traffic descriptor type and -- the associated parameters." -- ::= { atmMIBGroups 2 } -- -- atmVpcTerminationGroup OBJECT-GROUP -- OBJECTS {atmVplOperStatus, atmVplAdminStatus, -- atmVplLastChange, -- atmVplReceiveTrafficDescrIndex, -- atmVplTransmitTrafficDescrIndex, -- atmVplRowStatus } -- STATUS deprecated -- DESCRIPTION -- "A collection of objects providing -- information about a VPL at an ATM interface -- which terminates a VPC -- (i.e., one which is NOT cross-connected -- to other VPLs)." -- ::= { atmMIBGroups 5 } -- -- atmVccTerminationGroup OBJECT-GROUP -- OBJECTS {atmVclOperStatus, atmVclAdminStatus, -- atmVclLastChange, -- atmVclReceiveTrafficDescrIndex, -- atmVclTransmitTrafficDescrIndex, -- atmVccAalType, atmVclRowStatus } -- STATUS deprecated -- DESCRIPTION -- "A collection of objects providing information -- about a VCL at an ATM interface -- which terminates a VCC (i.e., one which is -- NOT cross-connected to other VCLs)." -- ::= { atmMIBGroups 6 } -- -- atmVpCrossConnectGroup OBJECT-GROUP -- OBJECTS { atmVplReceiveTrafficDescrIndex, -- atmVplTransmitTrafficDescrIndex, -- atmVplOperStatus, atmVplRowStatus, -- atmVpCrossConnectAdminStatus, -- atmVpCrossConnectL2HOperStatus, -- atmVpCrossConnectH2LOperStatus, -- atmVpCrossConnectL2HLastChange, -- atmVpCrossConnectH2LLastChange, -- atmVpCrossConnectRowStatus, -- atmVplCrossConnectIdentifier, -- atmVpCrossConnectIndexNext } -- STATUS deprecated -- DESCRIPTION -- "A collection of objects providing -- information about a VP cross-connect -- and the associated VPLs that are -- cross-connected together." -- ::= { atmMIBGroups 7 } -- -- atmVcCrossConnectGroup OBJECT-GROUP -- OBJECTS { atmVclReceiveTrafficDescrIndex, -- atmVclTransmitTrafficDescrIndex, -- atmVclOperStatus, atmVclRowStatus, -- atmVcCrossConnectAdminStatus, -- atmVcCrossConnectL2HOperStatus, -- atmVcCrossConnectH2LOperStatus, -- atmVcCrossConnectL2HLastChange, -- atmVcCrossConnectH2LLastChange, -- atmVcCrossConnectRowStatus, -- atmVclCrossConnectIdentifier, -- atmVcCrossConnectIndexNext } -- STATUS deprecated -- DESCRIPTION -- "A collection of objects providing -- information about a VC cross-connect -- and the associated VCLs that are -- cross-connected together." -- ::= { atmMIBGroups 8 } -- -- -- -- {atmMIB 3} has been used by [19]. END